讯享网

第一次编译的固件，失败！

Boot and Recovery Environment for Embedded Devices Copyright (C) 2018 HackPascal <[email protected]> Build date 2018-03-23 [git-994feec] Version 1.1 (r1211) DRAM: 32MB Platform: Qualcomm Atheros QCA953X rev 2 Board: Generic board Clocks: CPU: 550MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz Flash: Macronix MX25L6435E (8MB) on ath79-spi ag71xx-eth: MAC address is invalid, using default settings. ag71xx-eth: Using MAC address 00:13:74:00:00:01 Waiting for auto-negotiation complete ... OK eth0: Atheros AR8228/AR8229 rev 1 Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0 Press any key to interrupt autoboot ... 2 Autoboot aborted due to button press. Starting breed built-in shell breed> breed> breed> breed> boot Usage: boot mem <addr> - Boot from memory address or memory-mapped address boot flash [bank <n>] <addr> - Boot from flash boot linux <addr> - Boot linux kernel at <addr> boot raw <addr> - Disable interrupts and jump to <addr> boot breed <addr> - Boot given breed file at <addr> breed> boot flash Usage: boot mem <addr> - Boot from memory address or memory-mapped address boot flash [bank <n>] <addr> - Boot from flash boot linux <addr> - Boot linux kernel at <addr> boot raw <addr> - Disable interrupts and jump to <addr> boot breed <addr> - Boot given breed file at <addr> breed> reboot Unrecognised command: reboot Type 'help' to get available commands. breed> ps Unrecognised command: ps Type 'help' to get available commands. breed> help Available commands: about - About this bootloader abstatus - Interrupt status of autoboot arp - Display ARP table autoboot - Detect firmware type and boot automatically boot - Boot firmware btntst - Test GPIO of buttons dhcp - Display DHCP leases env - Environment variables utility envconf - Configure environment variable block exit - Exit from telnet flash - Flash utility gpio - GPIO utilities help - Show available commands mdio - MDIO utility mem - Memory operation utilities net - Network control netstat - Display network state reset - Restart device setbrg - Set baudrate spi - SPI utility sysinfo - Display system information thread - Display all threads wget - Retrieval file through HTTP breed> autoboot Trying to boot firmware from 0x9f ... U-Boot firmware image header detected. Image Name: MIPS OpenWrt Linux-3.3.8 Data Size:  Bytes Load Address:  Entry Point:  Uncompressing data (LZMA) ... done. Flushing cache ... done. Starting kernel at 0x... [ 0.000000] Linux version 3.3.8 (hades@hades) (gcc version 4.6.3  (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Wed May 16 16:16:25 CST 2018 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9531 rev 2 [ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 0 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00002000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00002000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: board=AP143 console=ttyS0, mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6336k(rootfs),1472k(kernel),64k(art),7744k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: